Roller Screed FAQs

• Honda Warranty - Your local Honda dealer can assist with warranty issues should they arise with yoru engine. MFC does not hold a warrantly on the Honda Engine.
• Manufacture Warranty - MFC has a 90 day limited warranty. See warranty for details

The Speed Screed® ROLLER is a variable length triple tube roller system that allows users to easily swap rollers and extension frames between jobs that require different pour widths. With rollers and extensions available from 10’ to 32’ in single foot increments, almost any job can be easily handled with this machine.

A roller screed consists of mechanized seamless pipes that spin against the concrete as contractors drive the unit over form rails. Roller screeds do not vibrate the concrete, so if vibration is engineered into a project a contractor will have to perform vibration manually.

Rolling screeds are more effective than vibrating screeds for pervious paving, low slump concrete, and slope paving.                                               

Vibratory Screeds do a slightly better job of leveling, but a considerably better job of consolidating.

Minimum length = 10 feet  Maximum Length = 32 feet.  Each of the three rollers utilize a bolting flange and are symmetrical which makes changing machine length quick and easy. The rollers can be orientated in either direction and can be mounted in any position. To replace or swap roller lengths follow the procedures listed in the Owners Manual.

Up to a 1" slump with adequate vibration.

A 22hp Honda Engine with a simple operator interface. Equipped with a dual joystick control and smart expandable system.

One person can operate the Speed Screed® ROLLER. NEVER allow anyone to operate this equipment without proper training. 

Minimum 3' wider than pour width, but recommend 4' wider than pour width.

16" - Will work with 16" forms. Adjustment of kickstand, foot assembly required.

Yes. The "Slinger" is adjustable up to 1" above finished slab height. Tube is preset from factory at 1/8" above slab height.

Yes. ALWAYS use OEM replacement parts. Contact MFC at 414-964-4550 for assistance.

OPERATION & PARTS MANUAL

Hydraulic Oil Reservoir (ISO 46): 10 gallons [37.85L]

Diameter: 8” SCH.40 Pipe (Ø8.625”) [Ø219.1mm]Wall thickness: 0.322” [8.18mm]Weight per foot: 28.55 lbs. [12.95kg]

2”x2”x1/8” steel tubes
6"x2"x1/8" steel tubes

12 gallon tank - Unleaded 86 octane or higher

Honda recommends a SAE 10W-30 or 5W-30 motor oil for general use. Use a full synthetic 5W-30 for starting/operating temperatures between 5°F (-15°C) and -13°F (-25°C). For other viscosities and recommendations, see Honda Owner’s manual.

iGX700 22hp Honda Engine  Air-cooled 4-stroke OHV - Intuitive engine automatically increases throttle when required reducing fuel consumption. Eliminates need for choke and reduces chance of engine flooding.

The hydraulic system utilizes an ISO 46 hydraulic oil. The hydraulic oil filter should be replaced every 500 hours or each year, and the full hydraulic system should be drained each season. When replacing the oil, make sure to clean out any loose particulate at the bottom of the hydraulic tank before refilling with fresh ISO 46 hydradraulic oil.

Machine weight (15’): 3,537 lbs. [1604kg] Approximate weight per foot for additions: 119 lbs. [54kg]

Daily Maintenance: Spray form release oil on any surfaces that will be in contact with concrete Check for loose roller connection hardware Check fuel level Check engine oil level1 Check engine air cleaner Check hydraulic oil level.                      

Weekly Maintenance: Check for loose hardware on engine end frame, lite (idler) end frame, and extension frames.                                                     

Seasonal Maintenance: Replace hydraulic oil & filters Change engine oil and filters (see Honda manual for additional recommendations).

Contact Metal Forms directly Office: 414-964-4550 or Submit an online Quote Request

Flatbed required - Roller Screed is shipped fully assembled and ready to use.

When loading and unloading your machines from a flat-bed or trailer, always use either the (4) provided lifting-eyes with shackles and chains rated above the maximum weight of your machine or the provided adjustable fork pocket assemblies. The lifting eyes are attached to the extension frame and can be moved to adjust the picking points for different length machines. The fork pockets can be adjusted by loosening the square U-bolts. Always place the picking support bars or fork pockets at an equal distance from the center of gravity of the machine.

Typical lead time is 4-6 weeks from date of order. Fastest in the industry!

• Spray system 
• Walkway